Tramex RWS Roof and Wall Moisture Scanner :: Non Invasive Moisture Meters :: Moisture Meters :: Tool Experts-Home Inspection, Maintenance, and Testing Instruments

Details


SKU	RWS
Weight	4.30 lbs
Price:	$1249.95

Options

Quantity

Add to cart

Wish List

Tramex RWS Roof and Wall Moisture Scanner

Click Here To See Manufacturers Specifications

Multi-mode moisture scanner for non-destructive moisture detection and leak tracing in walls and roofing.

The Tramex RWS incorporates two of Tramex`s well-known moisture scanners, the Leak Seeker for Roofing and the Wet Wall Detector for EIFS, incorporating all the benefits and features of both these time proven instruments into one.

The Tramex RWS has dual operating modes for EIFS and Roofing. Each of these modes has 2 ranges of sensitivity for both deep and low penetration sensitivity enabling the scanning of Roofing and EIFS with a signal penetration ranging from the surface up to approximately 4". Evaluate moisture non-destructively and trace leaks back to the source.

Use on: Built-Up, Non-Conductive Single Ply, Modified and Foamed Roofing Systems, Exterior Insulation and Finishing Systems (EIFS).

Hold function, Instant clear readings.

The Problems of Excess Moisture in the Building Envelope.

By visual inspection, the location of excess moisture and decay in or behind EIFS or Roofing Systems can be difficult and near impossible, as normal evidence of this moisture and decay may not be visible on either side of the wall or roof.

Excess moisture can be hidden and trapped in the substrate and within the thickness of the wall or roof construction.

If these conditions are allowed to continue the moisture will increase, eventually leading to rot and decay and possible failure of the system and the structure.

Also wet insulation loses its thermal value resulting in unnecessary heat loss or gain and thermal movement in the structure. Early detection of wet areas and corrective remedial action makes good economic sense.

How does the RWS Detector Work?

The Tramex RWS is an electronic hand-held Moisture Scanner and Detector working on the principle of electrical impedance. With impedance measurement, harmless signals are transmitted from the electrodes at the base of the instrument deep into the thickness of the area under test.

These signals measure the change in electrical impedance which is translated into a relative moisture content reading and instantly displayed on the clear large analog dial. Readings are instant and continuous.

The Tramex RWS is also fitted with an audible device which sounds at high readings.

The Tramex RWS gives vital information necessary to evaluate and carry out moisture assessment on the condition of most fiber reinforced EIFS wall cladding systems, roofing systems such as built up, non-conductive single ply, modified and foam roofing at an affordable cost and without complications.

The Fast Non-Destructive Way to Detect Excess Moisture

For EIFS, the Tramex RWS has been especially developed to aid in the detection, location and tracing of excess moisture within the weatherproofing coatings or coverings, and deep into the insulation and substrate to detect excess moisture in the sheathing and the wood studding of EIFS systems. For Roofing it will detect interply moisture, excess moisture in the insulation material, and moisture in or on non-conductive roof decks.

It is easy and fast to use, light to carry and can be operated with one hand. Having detected and located the areas of excess moisture the Tramex RWS can be of great benefit in tracing this moisture back to its point of ingress or source.

SPECIFICATIONS:
Dimensions: 125mm x 275mm x 75mm / 4.75x 11 x 3
Weight: 1.8kg (4lbs)
Power Supply: One 9 volt battery
Sensitivity: Four ranges:
EIFS Mode with high and low sensitivity.
Roofing Mode with high and low sensitivity.
Accessories: Leather carrying case. Telescopic handle for use on roofing only.
Limitations: Roofing: EPDM, Butyl rubber roofing and other conductive roofing. EIFS: Hard Coat Stucco, wire lath or wire mesh reinforced finishes.

WARRANTY:
The RWS carries a full parts and labor warranty for a period of one year from the date of first purchase.