Categories
Previous image
Mold Test Slides - Zefon Bio Tape
Next image
Zoom image

Mold Test Slides - Zefon Bio Tape

SKU# - ZBT

Zefon Bio Tape Slides allow you to quickly take a sample of suspected mold and measure the relative degree of contamination.


  • $37.99
Qty:  
Add a different product to compare

Zefon Bio Tape - Mold Test Slides

Zefon Bio Tape™ provides a standardized sampling method for the determination of mold, microbial, bio aerosol, and inorganic dust contamination. 
 
Zefon Bio Tape consists of a flexible plastic microscope slide with a pre-defined adhesive area. A center-line marker on the slide aids the user in locating the center when taking the sample and also aids the laboratory analyst in finding the center of the sample. Each mold slide is provided with a unique serial number for traceability and packed in a slide mailer to prevent cross contamination.
 
Zefon Bio Tape is now compatible with both optical microscopy and scanning electron microscopy (SEM). This provides the ability to perform optical and SEM analysis along with an x-ray analysis on the exact same air surface sample and exact same particles. 

Zefon Bio-Tape Features:

  • Provides sample consistency and uniformity
  • Easier to handle than tape
  • Individually Serialized for Traceability
  • Prevents Cross Contamination
  • Eliminates problems of placing tape in a zip bag, or broken slides during transport
  • Requires less laboratory prep time.
  • Ideal for mold sampling and testing
  • Compatible with both optical microscope and scanning electron microscopy (SEM)

Sampling Procedure:

  1. Remove slide from provided slide mailer.
  2. Document the sample location on the slide label and complete any required documentation for the laboratory.
  3. Peel off protective liner from slide to expose adhesive.
  4. Place slide with the adhesive side down on the surface to be sampled. (Use the centering line to orient the adhesive over the exact sample location desired).
  5. Gently press down to ensure contact is made. Do not press down hard. The adhesive is very tacky and only needs to be pressed gently.
  6. Carefully remove slide from surface and place back into slide mailer. Do Not replace the plastic “Peel” liner.
  7. Send slide to laboratory for analysis.

    Note: Multiple samples should be collected from both suspect and non-suspect (control) areas for comparison.


Using Zefon Bio-Tape™ mold testing slides helps provide more consistency in your samples. This is because each sample uses the same amount of adhesive surface area and the provided packaging offers protection during shipment to the laboratory. When the laboratory receives your sample, there will be no guessing where the sample area is and no sticky mess of tape to deal with.
 
Available in 25, 50 and 500 packs

    • Weight
      1 lbs
    • SKU
      ZBT0025
  • Manufacturer
    Zefon
  • Pack Size
    25 Pack, 50 Pack, 500 Pack

Product questions

  • Lonnie
    08/01/2021, 11:14 AM

    Where do you send the sample is there a specific place

    Administrator
    08/02/2021, 09:05 AM

    A mold testing lab would be able to test your sample. There are labs all over the country that can meet your needs.

  • Mark
    09/27/2020, 10:55 AM

    How do you use this? Product arrived with no instructions

    Administrator
    09/28/2020, 10:02 AM

    Sampling Procedure:
    1. Remove slide from provided slide mailer.
    2. Document the sample location on the slide label and complete any required documentation for the laboratory.
    3. Peel off protective liner from slide to expose adhesive.
    4. Place slide with the adhesive side down on the surface to be sampled. (Use the centering line to orient the adhesive over the exact sample location desired).
    5. Gently press down to ensure contact is made. Do not press down hard. The adhesive is very tacky and only needs to be pressed gently.
    6. Carefully remove slide from surface and place back into slide mailer. Do Not replace the plastic “Peel” liner.
    7. Send slide to laboratory for analysis.

    Note: Multiple samples should be collected from both suspect and non-suspect (control) areas for comparison.

Related products