:
from
to
Reaper Jetter Nozzle 3/8 Inch - RS 624
SKU: RS624
SKU# - RS624
Reaper Jetter Nozzle - Ideal for 3"-6" Lines
These heavy-duty, high impact nozzles are constructed with stainless steel housing and tungsten carbide wear surfaces to withstand harsh environments and provide longer life than ceramic nozzles.
Reaper Jetter Nozzle 3/8 Inch - RS 624
Please see Chart Below for Accurate Nozzle Sizing
The Reaper’s rotating front jet is a 0-degree, straight water stream that blasts at up to 4000 PSI while rotating at an optimal speed to form a 24-degree cone of coverage. Reaper’s rear jets create maximum thrusting and pulling power.
Reaper Jetter Nozzle 3/8" Specifications:
Minimum Inlet Pressure: 1,500 PSI (103 bar)
Maximum Inlet Pressure: 4,000 PSI (276 bar)
Maximum Water Temperature: 180ºF (+82ºC)
Housing Material: Stainless Steel
Nozzle Tip & Seat Material: Tungsten Carbide
Inlet Connection Thread: 3/8” FNPT
Front (Rotating) Spray Angle: 24º
Rear (Static) Spray Angle: 20º
Flow Rate Chart:
| Flow Rate | @ 1500 | @2000 | @2500 | @3000 | @3500 | @4000 |
| Nozzle Size 6.0 #1003031-060 | 3.7 GPM | 4.2 GPM | 4.7 GPM | 5.2 GPM | 5.6 GPM | 6.0 GPM |
| 9.0 #1003031-090 | 5.5 GPM | 6.4 GPM | 7.1 GPM | 7.8 GPM | 8.4 GPM | 9.0 GPM |
| 12.0 #1003031-120 | 7.3 GPM | 8.5 GPM | 9.5 GPM | 10.4 GPM | 11.2 GPM | 12.0 GPM |
Product questions
- 12/20/2024, 01:34 AM
Will it work well with a 4.5 gpm 3500 psi unit?
12/20/2024, 10:47 AMYou would get maximum performance at 5.6 gpm. This is a small difference for orifice sizing so you will still get strong performance with this nozzle.
- 04/02/2024, 09:57 PM
I have a 6.6gpm 4500psi cart jetter with 3/8” hose. Will the 6.6gpm nozzle let 6.6 gpm through if i turn the pressure down? What is optimal to cut roots
04/03/2024, 11:03 AMYou shouldn't have a problem with that output. That nozzle has a 6 orifice so you will be very close to optimal output at the 4500psi 6.6gpm.
- 02/29/2024, 10:25 AM
4000psi, 5.5gpm will the reaper work? 3/8 line.
02/29/2024, 11:06 AMYes it will work. You will get a little better performance by turning your psi down. You would get a bit better performance going to a 1/4" line to optimize your pumps output better.
- 01/26/2024, 11:19 PM
I have an 18 gpm @ 4000 psi , I use a 200 ft 3/8 hose connected to a 1/2 hose, do you have to size the nozzle to these specs , and or what would it be which nozzle for the 3/8
01/27/2024, 11:21 AMThat output is more gpm than the 3/8 nozzles are made for and more than we would typically recommend for a 3/8 nozzle. The RS830 1/2 inch nozzle would match up perfectly with your machine.
Related products
- Free shipping
